Skip to content
TACHYONS ENERGYPRIVATE LIMITED

CONTROL & RELAY PANELS

Control and Relay Panel Wiring and CRP Erection for Substations

Tachyons Energy Private Limited erects and wires control and relay panels (CRPs) for substations from 11kV to 440kV, including simplex and duplex relay panels, SCADA / RTU marshalling kiosks, ACDB / DCDB auxiliary boards and battery charger systems. Every core is ferrule-coded and terminated to the approved scheme drawings, then tested point to point before relays are injected and protection is proven through to the breaker. The company works for utilities, industries and generation plants from Kerala, India.

  • Simplex / Duplex CRP
  • SCADA / RTU
  • ACDB / DCDB
  • 110V / 220V DC

What a control and relay panel does

A control and relay panel (CRP) is the cabinet in a substation control room that holds the protection relays, control switches, meters and annunciators for one or more bays. It receives current and voltage signals from CTs and PTs in the yard, decides when a fault must be cleared, and sends trip and close commands to the circuit breakers. Simplex panels have all devices on the front; duplex panels have a front control face and a rear relay face separated by an inspection corridor.

CRP erection and ferrule-coded wiring

Panel suites are positioned, levelled and bolted in the control room, then wired strictly to the approved schematic and wiring diagrams. Wiring discipline matters because a single wrong core in a CT or trip circuit can cause a protection mal-operation.

  • Base-channel checks, suite alignment, inter-panel bolting and plinth sealing
  • Gland plates, cable entry and panel earth-bar connection to the station earth
  • Every core ferruled at both ends to the scheme wire numbering
  • Conductor sizes per scheme drawing, commonly 2.5 mm² Cu for CT circuits and 1.5 mm² for control
  • Crimped lugs or pin terminals, segregated terminal rows for CT, PT, AC and DC circuits
  • Numerical relays, lockout (86) and trip-circuit supervision relays, test terminal blocks, mimic and TNC switches

SCADA / RTU, ACDB / DCDB and battery chargers

Around the relay panels sit the boards that connect the substation to remote control and keep protection supplied. Tachyons Energy installs and wires these as part of the same scope so that signals and auxiliary supplies are tested together.

  • SCADA / RTU marshalling kiosks for digital inputs, outputs and analogue signals to the I/O list
  • Interposing relays, transducers and surge protection where specified
  • ACDB: 415V AC auxiliary distribution with incomer changeover and MCB / MCCB feeders
  • DCDB: 110V or 220V DC distribution to protection, control and closing circuits as specified
  • DC earth-fault and insulation monitoring with supply-fail alarms
  • Battery stand erection, cell interconnection and float / boost charger commissioning

Testing before energisation

Before any auxiliary supply is switched on, every core is checked for continuity and each circuit group for insulation resistance. Relays are then tested by secondary injection against the approved settings file, and complete schemes are proven through to breaker trip and close.

  • Point-to-point continuity and insulation resistance records
  • Secondary injection of numerical and electromechanical relays
  • Trip, close, interlock and lockout scheme checks
  • Annunciator window tests and alarm list sign-off
  • SCADA point-by-point I/O verification against the signal list

HOW THE WORK RUNS

How we deliver control & relay panels

  1. 01

    Drawing and scheme review

    Review of the single-line diagram, protection schematics, wiring diagrams, cable schedule and I/O list before panels reach site.

  2. 02

    Panel receipt and erection

    Inspection of panels on arrival, positioning on base channels, alignment, bolting, sealing and earthing of the suite.

  3. 03

    Internal and inter-panel wiring

    Ferrule-coded wiring of relays, meters, switches and test blocks, inter-panel bus wiring and reconnection of shipping splits.

  4. 04

    Field cable termination

    Control cables from the yard glanded and terminated at CRPs, marshalling kiosks, ACDB / DCDB and SCADA panels to the cable schedule.

  5. 05

    Testing and scheme proving

    Continuity and IR checks, secondary injection, trip and interlock tests and SCADA end-to-end checks, with as-left settings recorded.

QUESTIONS & ANSWERS

Control & Relay Panels: common questions

Straight answers to what clients ask us most before a project starts.

What is a CRP in a substation?

CRP stands for control and relay panel. It houses the protection relays, control switches, indication, metering and annunciation for the substation bays, and issues trip and close commands to circuit breakers. Each feeder, transformer or bus section normally has its own CRP or a section of a panel suite.

What is the difference between a simplex and a duplex relay panel?

A simplex panel has all control and protection devices mounted on its front face, with access from the front and rear. A duplex panel has a front control face with mimic, switches and meters, and a rear relay face, separated by an inspection corridor inside the panel. Duplex panels are common in larger substations where many devices are needed per bay.

Why is ferrule coding important in panel wiring?

Ferrules mark each core with its wire number from the scheme drawing at both ends, so any circuit can be traced, tested and modified without guesswork. This reduces wiring errors during installation and makes fault finding faster during operation. Missing or wrong ferrules are a common cause of commissioning delays.

What are ACDB and DCDB panels?

An ACDB (AC distribution board) distributes the 415V AC auxiliary supply in a substation to lighting, heaters, chargers and equipment motors. A DCDB (DC distribution board) distributes DC from the station battery, commonly at 110V or 220V, to protection relays, control circuits and breaker closing and tripping coils. The DC system keeps protection working even if AC auxiliary supply is lost.

What tests are done on control and relay panels before commissioning?

Typical tests are point-to-point continuity of every core, insulation resistance of each circuit group, secondary injection of each relay against its settings, and functional checks of trip, close, interlock and alarm circuits. Where SCADA is involved, each signal is verified against the I/O list. Results and as-left relay settings are handed over as part of the test records.

Does Tachyons Energy manufacture or only wire relay panels?

Tachyons Energy erects, wires and tests control and relay panel suites at site, including custom panel erection, SCADA / RTU kiosks, ACDB / DCDB boards and battery charger integration. For panel supply or manufacturing requirements, the scope can be discussed through a request for quotation.